Research Progress and Prospects of Bipolar Plate Materials for Proton Exchange Membrane Fuel Cells

Authors

  • Wenjun Li

DOI:

https://doi.org/10.54097/r7damr19

Keywords:

PEMFC, Bipolar plates, Conductivity, Dual Percolation Effects.

Abstract

The bipolar plate is an essential component of proton exchange membrane fuel cells (PEMFC), with crucial functions such as gas separation, cooling, conduction, heat dissipation, and water ejection. The advancement of proton exchange membrane fuel cell technology relies on the performance of the bipolar plate. Recognizing the significance of bipolar plates for PEMFC functionality, researchers have been striving to create bipolar plates with high conductivity, good gas tightness, appropriate mechanical properties, corrosion resistance, and cost-effectiveness. This paper provides a detailed analysis of recent research progress on bipolar plates, aiming to contribute to the development of new and optimized products in the PEM fuel cell industry. The study in this paper focuses on three aspects: (1) Introduction to the polymer electrolyte membrane (PEM) fuel cell technology system and development directions, (2) Discussion on the structure of carbon-based fillers and their impact on the final electrical performance of composite bipolar plates, (3) Introduction to the Dual Percolation Effects of resins and Their Applications.

Downloads

Download data is not yet available.

References

Jiao K, Xuan J, Du Q, et al. Designing the next generation of proton-exchange membrane fuel cells [J]. Nature, 2021, 595 (7867): 361 - 369.

Debe M K. Electrocatalyst approaches and challenges for automotive fuel cells [J]. Nature, 2012, 486 (7401): 43 - 51.

Dundar F, Dur E, Mahabunphachai S, et al. Corrosion resistance characteristics of stamped and hydroformed proton exchange membrane fuel cell metallic bipolar plates [J]. Journal of Power sources, 2010, 195 (11): 3546 - 3552.

Borup R, Meyers J, Pivovar B, et al. Scientific aspects of polymer electrolyte fuel cell durability and degradation [J]. Chemical reviews, 2007, 107 (10): 3904 - 3951. [1]

Antunes R A, De Oliveira M C L, Ett G, et al. Carbon materials in composite bipolar plates for polymer electrolyte membrane fuel cells: A review of the main challenges to improve electrical performance [J]. Journal of Power Sources, 2011, 196 (6): 2945 - 2961.

Lim J W, Kim M. Conductive particles embedded carbon composite bipolar plates for proton exchange membrane fuel cells [J]. Composite Structures, 2014, 108: 757 - 766.

Jiang X, Drzal L T. Exploring the potential of exfoliated graphene nanoplatelets as the conductive filler in polymeric nanocomposites for bipolar plates[J]. Journal of Power Sources, 2012, 218: 297 - 306.

Shen K, Cao X, Huang Z H, et al. Microstructure and thermal expansion behavior of natural microcrystalline graphite [J]. Carbon, 2021, 177: 90 - 96.

Jiao S, Liu M, Li Y, et al. Emerging hydrovoltaic technology based on carbon black and porous carbon materials: A mini review [J]. Carbon, 2022, 193: 339 - 355.

You R, Liu Y Q, Hao Y L, et al. Laser fabrication of graphene‐based flexible electronics [J]. Advanced Materials, 2020, 32 (15): 1901981.

Chung H T, Won J H, Zelenay P. Active and stable carbon nanotube/nanoparticle composite electrocatalyst for oxygen reduction [J]. Nature communications, 2013, 4 (1): 1922.

Zheng Y, Yu Z, Zhang S, et al. A molecular design approach towards elastic and multifunctional polymer electronics [J]. Nature communications, 2021, 12 (1): 5701.

Mun J, Kang J, Zheng Y, et al. Conjugated carbon cyclic nanorings as additives for intrinsically stretchable semiconducting polymers [J]. Advanced Materials, 2019, 31 (42): 1903912.

Zhang M, Gao Y, Zhang Y, et al. Preparation and properties of polyphenylene sulfide/oxidized-polyphenylene sulfide composite membranes [J]. Reactive and Functional Polymers, 2021, 160: 104842.

Li W, Li Z, Bertelsmann K, et al. Portable low‐pressure solar steaming‐collection unisystem with polypyrrole origamis[J]. Advanced Materials, 2019, 31 (29): 1900720.

Gong X, Meng Y, Lu J, et al. A Review on lignin‐based phenolic resin adhesive [J]. Macromolecular Chemistry and Physics, 2022, 223 (4): 2100434.

Li G Z, Wang L, Toghiani H, et al. Viscoelastic and mechanical properties of vinyl ester (VE)/multifunctional polyhedral oligomeric silsesquioxane (POSS) nanocomposites and multifunctional POSS–styrene copolymers [J]. Polymer, 2002, 43 (15): 4167 - 4176.

Wang J, Zhang Q, Cheng Y, et al. Self-reinforced composites based on polypropylene fiber and graphene nano-platelets/polypropylene film [J]. Carbon, 2022, 189: 586 - 595.

Zervoudakis A J, Sample C S, Peng X, et al. Dihydroxy polyethylene additives for compatibilization and mechanical recycling of polyethylene terephthalate/polyethylene mixed plastic waste [J]. ACS Macro Letters, 2022, 11 (12): 1396 - 1402.

Sun Z, Sun L, Zhu C, et al. Effect of Polyphenylene Sulphide Particles and Films on the Properties of Polyphenylene Sulphide Composites [J]. Materials, 2022, 15 (21): 7616.

Jiang F, Liao W, Ayukawa T, et al. Enhanced performance and durability of composite bipolar plate with surface modification of cactus-like carbon nanofibers [J]. Journal of Power Sources, 2021, 482: 228903.

Jeong K I, Jeong J M, Oh J, et al. An integrated composite structure with reduced electrode/bipolar plate contact resistance for vanadium redox flow battery [J]. Composites Part B: Engineering, 2022, 233: 109657.

Chen J, Fan R, Qin N, et al. Recent advances on materials and technologies of composite bipolar plate for proton exchange membrane fuel cell [J]. Journal of Power Sources, 2024, 594: 234009.

Kwiecińska B, Petersen H I. Graphite, semi-graphite, natural coke, and natural char classification—ICCP system [J]. International Journal of Coal Geology, 2004, 57 (2): 99 - 116.

Lee D, Lim J W, Nam S, et al. Method for exposing carbon fibers on composite bipolar plates [J]. Composite Structures, 2015, 134: 1 - 9.

Wei B, Yang S. Polymer composites with expanded graphite network with superior thermal conductivity and electromagnetic interference shielding performance [J]. Chemical Engineering Journal, 2021, 404: 126437.

Sengupta R, Bhattacharya M, Bandyopadhyay S, et al. A review on the mechanical and electrical properties of graphite and modified graphite reinforced polymer composites [J]. Progress in polymer science, 2011, 36 (5): 638 - 670.

Kuan H C, Ma C C M, Chen K H, et al. Preparation, electrical, mechanical and thermal properties of composite bipolar plate for a fuel cell [J]. Journal of Power Sources, 2004, 134 (1): 7 - 17.

Derieth T, Bandlamudi G, Beckhaus P, et al. Development of highly filled graphite compounds as bipolar plate materials for low and high temperature PEM fuel cells [J]. Journal of New Materials for Electrochemical Systems, 2008, 11 (1): 21.

Kang K, Park S, Ju H. Effects of type of graphite conductive filler on the performance of a composite bipolar plate for fuel cells [J]. Solid State Ionics, 2014, 262: 332-336.

Heo S I, Yun J C, Oh K S, et al. Influence of particle size and shape on electrical and mechanical properties of graphite reinforced conductive polymer composites for the bipolar plate of PEM fuel cells [J]. Advanced composite materials, 2006, 15 (1): 115 - 126.

Kim M, Yu H N, Lim J W. Bipolar plates made of plain weave carbon/epoxy composite for proton exchange membrane fuel cell [J]. International journal of hydrogen energy, 2012, 37 (5): 4300 - 4308.

Chen J, Fan R, Qin N, et al. Recent advances on materials and technologies of composite bipolar plate for proton exchange membrane fuel cell [J]. Journal of Power Sources, 2024, 594: 234009.

Rafi-ud-din, Arshad M, Saleem A, et al. Fabrication and characterization of bipolar plates of vinyl ester resin/graphite-based composite for polymer electrolyte membrane fuel cells [J]. Journal of Thermoplastic Composite Materials, 2016, 29 (10): 1315 - 1331.

Dhakate S R, Sharma S, Borah M, et al. Expanded graphite-based electrically conductive composites as bipolar plate for PEM fuel cell [J]. international journal of hydrogen energy, 2008, 33 (23): 7146 - 7152.

Shornikova O N, Sorokina N E, Avdeev V V. Preparation and properties of exfoliated graphite doped with nickel and cobalt oxides [J]. Inorganic Materials, 2007, 43: 938 - 944.

Lin C H, Tsai S Y. An investigation of coated aluminium bipolar plates for PEMFC[J]. Applied energy, 2012, 100: 87 - 92.

Feng K, Li Z, Lu F, et al. Corrosion resistance and electrical properties of carbon/chromium–titanium–nitride multilayer coatings on stainless steel [J]. Journal of Power Sources, 2014, 249: 299 - 305.

Zhao L, Ding B, Qin X Y, et al. Revisiting the roles of natural graphite in ongoing lithium‐ion batteries [J]. Advanced Materials, 2022, 34 (18): 2106704.

Ji S, Hwang Y S, Park T, et al. Graphite foil based assembled bipolar plates for polymer electrolyte fuel cells [J]. International Journal of Precision Engineering and Manufacturing, 2012, 13: 2183 - 2186.

Wang Y, Wang J, Yin B, et al. State-of-the-art in bipolar of proton exchange membrane fuel cell[C]//5th International Symposium on Advanced Optical Manufacturing and Testing Technologies: Smart Structures and Materials in Manufacturing and Testing. SPIE, 2010, 7659: 161 - 165.

Zheng W, Wong S C. Electrical conductivity and dielectric properties of PMMA/expanded graphite composites [J]. Composites Science and Technology, 2003, 63 (2): 225 - 235.

Zhao Y F, Xiao M, Wang S J, et al. Preparation and properties of electrically conductive PPS/expanded graphite nanocomposites [J]. Composites science and technology, 2007, 67 (11-12): 2528 - 2534.

Lv X, Wang R, Liu W, et al. Surface and interface properties of carbon fiber composites under cyclical aging [J]. Applied surface science, 2011, 257 (24): 10459 - 10464.

Antunes R A, De Oliveira M C L, Ett G, et al. Carbon materials in composite bipolar plates for polymer electrolyte membrane fuel cells: A review of the main challenges to improve electrical performance [J]. Journal of Power Sources, 2011, 196 (6): 2945 - 2961.

Zhao Y H, Zhang Y F, Bai S L, et al. Carbon fibre/graphene foam/polymer composites with enhanced mechanical and thermal properties [J]. Composites Part B: Engineering, 2016, 94: 102 - 108.

Maheshwari P H, Mathur R B, Dhami T L. Fabrication of high strength and a low weight composite bipolar plate for fuel cell applications[J]. Journal of Power Sources, 2007, 173 (1): 394 - 403.

Lee D, Choe J, Nam S, et al. Development of non-woven carbon felt composite bipolar plates using the soft layer method [J]. Composite Structures, 2017, 160: 976 - 982.

Jiang B, Stübler N, Wu W, et al. Manufacturing and characterization of bipolar fuel cell plate with textile reinforced polymer composites [J]. Materials & Design (1980-2015), 2015, 65: 1011 - 1020.

Radzuan N A M, Zakaria M Y, Sulong A B, et al. The effect of milled carbon fibre filler on electrical conductivity in highly conductive polymer composites [J]. Composites Part B: Engineering, 2017, 110: 153 - 160.

Zakaria M Y, Sulong A B, Sahari J, et al. Effect of the addition of milled carbon fiber as a secondary filler on the electrical conductivity of graphite/epoxy composites for electrically conductive material [J]. Composites Part B: Engineering, 2015, 83: 75 - 80.

Mathur R B, Dhakate S R, Gupta D K, et al. Effect of different carbon fillers on the properties of graphite composite bipolar plate [J]. Journal of Materials Processing Technology, 2008, 203 (1-3): 184 - 192.

Selamat M Z, Ahmad M S, Mohd Daud M A, et al. Preparation of Polymer Composite Bipolar Plate with Different Multi-Filler for Polymer Electrolyte Membrane Fuel Cell (PEMFC)[J]. Applied Mechanics and Materials, 2015, 699: 689 - 694.

Kim M, Lim J W, Kim K H. Bipolar plates made of carbon fabric/phenolic composite reinforced with carbon black for PEMFC [J]. Composite Structures, 2013, 96: 569 - 575.

Gautam R K, Kar K K. Synergistic effects of carbon fillers of phenolic resin based composite bipolar plates on the performance of PEM fuel cell [J]. Fuel Cells, 2016, 16 (2): 179 - 192.

Kuan H C, Ma C C M, Chen K H, et al. Preparation, electrical, mechanical and thermal properties of composite bipolar plate for a fuel cell [J]. Journal of Power Sources, 2004, 134 (1): 7 - 17.

Dhakate S R, Mathur R B, Kakati B K, et al. Properties of graphite-composite bipolar plate prepared by compression molding technique for PEM fuel cell [J]. International Journal of Hydrogen Energy, 2007, 32 (17): 4537 - 4543.

Suherman H, Sahari J, Sulong A B, et al. Properties of epoxy/carbon black/graphite composites for bipolar plate in polymer electrolyte membrane fuel cell [J]. Advanced Materials Research, 2014, 911: 8 - 12.

Radzuan N A M, Zakaria M Y, Sulong A B, et al. The effect of milled carbon fibre filler on electrical conductivity in highly conductive polymer composites [J]. Composites Part B: Engineering, 2017, 110: 153 - 160.

Gao X, Chen J, Xu R, et al. Research progress and prospect of the materials of bipolar plates for proton exchange membrane fuel cells (PEMFCs) [J]. International Journal of Hydrogen Energy, 2023.

Lee J H, Lee J S, Kuila T, et al. Effects of hybrid carbon fillers of polymer composite bipolar plates on the performance of direct methanol fuel cells [J]. Composites Part B: Engineering, 2013, 51: 98 - 105.

Suherman H, Sulong A B, Sahari J. Effect of the compression molding parameters on the in-plane and through-plane conductivity of carbon nanotubes/graphite/epoxy nanocomposites as bipolar plate material for a polymer electrolyte membrane fuel cell [J]. Ceramics International, 2013, 39 (2): 1277 - 1284.

Taherian R, Hadianfard M J, Golikand A N. Manufacture of a polymer-based carbon nanocomposite as bipolar plate of proton exchange membrane fuel cells [J]. Materials & Design, 2013, 49: 242 - 251.

Papageorgiou D G, Li Z, Liu M, et al. Mechanisms of mechanical reinforcement by graphene and carbon nanotubes in polymer nanocomposites [J]. Nanoscale, 2020, 12 (4): 2228 - 2267.

Corletto A, Shapter J G. Nanoscale patterning of carbon nanotubes: techniques, applications, and future[J]. Advanced Science, 2021, 8 (1): 2001778.

Xiong K, Wu W, Wang S, et al. Modeling, design, materials and fabrication of bipolar plates for proton exchange membrane fuel cell: A review [J]. Applied energy, 2021, 301: 117443.

Tariq M, Utkarsh, Syed N A, et al. Synergistic enrichment of electrically conductive polypropylene‐graphite composites for fuel cell bipolar plates [J]. International Journal of Energy Research, 2022, 46 (8): 10955 - 10964.

Selamat M Z, Ahmad M S, bin Daud M A, et al. Effect of carbon nanotubes on properties of graphite/carbon black/polypropylene nanocomposites[J]. Advanced Materials Research, 2013, 795: 29 - 34.

Radzuan N A M, Sulong A B, Somalu M R, et al. Fibre orientation effect on polypropylene/milled carbon fiber composites in the presence of carbon nanotubes or graphene as a secondary filler: Application on PEM fuel cell bipolar plate [J]. International journal of hydrogen energy, 2019, 44 (58): 30618 - 30626.

Bouatia S, Mighri F, Bousmina M. Development and characterisation of electrically conductive polymeric‐based blends for proton exchange membrane fuel cell bipolar plates [J]. Fuel Cells, 2008, 8 (2): 120 - 128.

Dhakate S R, Sharma S, Chauhan N, et al. CNTs nanostructuring effect on the properties of graphite composite bipolar plate [J]. International Journal of hydrogen energy, 2010, 35 (9): 4195 - 4200.

Darıcık F, Topcu A, Aydın K, et al. Carbon nanotube (CNT) modified carbon fiber/epoxy composite plates for the PEM fuel cell bipolar plate application [J]. International Journal of Hydrogen Energy, 2023, 48 (3): 1090 - 1106.

Suherman H, Sulong A B, Sahari J. Effect of the compression molding parameters on the in-plane and through-plane conductivity of carbon nanotubes/graphite/epoxy nanocomposites as bipolar plate material for a polymer electrolyte membrane fuel cell [J]. Ceramics International, 2013, 39 (2): 1277 - 1284.

Suherman H, Sahari J, Sulong A B. Electrical properties of carbon nanotubes-based epoxy nanocomposites for high electrically conductive plate[J]. Advanced Materials Research, 2011, 264: 559 - 564.

Radzuan N A M, Sulong A B, Somalu M R, et al. Fibre orientation effect on polypropylene/milled carbon fiber composites in the presence of carbon nanotubes or graphene as a secondary filler: Application on PEM fuel cell bipolar plate[J]. International journal of hydrogen energy, 2019, 44 (58): 30618 - 30626.

Mukherjee S, Bates A, Lee S C, et al. A review of the application of CNTs in PEM fuel cells[J]. International journal of green energy, 2015, 12 (8): 787 - 809.

Suherman H, Sulong A B, Sahari J. Effect of the compression molding parameters on the in-plane and through-plane conductivity of carbon nanotubes/graphite/epoxy nanocomposites as bipolar plate material for a polymer electrolyte membrane fuel cell [J]. Ceramics International, 2013, 39 (2): 1277 - 1284.

Duan Z, Qu Z, Ren Q, et al. Review of bipolar plate in redox flow batteries: Materials, structures, and manufacturing [J]. Electrochemical Energy Reviews, 2021, 4 (4): 718 - 756.

Zheng N, Xu Y, Zhao Q, et al. Dynamic covalent polymer networks: a molecular platform for designing functions beyond chemical recycling and self-healing [J]. Chemical Reviews, 2021, 121 (3): 1716 - 1745.

Taherian R, Nasr M. Performance and material selection of nanocomposite bipolar plate in proton exchange membrane fuel cells [J]. International journal of energy research, 2014, 38 (1): 94 - 105.

Raunija T S K, Gautam R K, Bhradwaj V M, et al. Low cost and rapidly processed randomly oriented carbon/carbon composite bipolar plate for PEM fuel cell[J]. Fuel Cells, 2016, 16 (6): 801 - 809.

Wan Z, Liang D, Lu L, et al. Fabrication of micro-flow channels on graphite composite bipolar plates using microplanning [J]. Journal of Central South University, 2015, 22 (8): 2963 - 2970.

Wang S, Ma S, Li Q, et al. Facile in situ preparation of high-performance epoxy vitrimer from renewable resources and its application in nondestructive recyclable carbon fiber composite [J]. Green chemistry, 2019, 21(6): 1484 - 1497.

Ghosh A, Verma A. Carbon‐polymer composite bipolar plate for HT‐PEMFC [J]. Fuel Cells, 2014, 14 (2): 259 - 265.

Pitchiya A P, Le N T, Putnam Z A, et al. Microporous graphite composites of tailorable porosity, surface wettability, and water permeability for fuel cell bipolar plates [J]. Industrial & Engineering Chemistry Research, 2021, 60 (28): 10203 - 10216.

Kim M, Lim J W, Kim K H. Bipolar plates made of carbon fabric/phenolic composite reinforced with carbon black for PEMFC [J]. Composite Structures, 2013, 96: 569 - 575.

Guan G, Kusakabe K, Ozono H, et al. Preparation of carbon microparticle assemblies from phenolic resin using an inverse opal templating method [J]. Journal of materials science, 2007, 42: 10196 - 10202.

Wang L J, Yang K X, Zhou Q, et al. Rhodamine mechanophore functionalized mechanochromic double network hydrogels with high sensitivity to stress [J]. Chinese Journal of Polymer Science, 2020, 38: 24 - 36.

Dai S, Li S, Xu G, et al. Direct synthesis of polar functionalized polyethylene thermoplastic elastomer [J]. Macromolecules, 2020, 53 (7): 2539 - 2546.

Schade M, Franzka S, Schröter A, et al. Chemical functionalization of carbon/polymer bipolar plate materials via oxygen plasma activation and subsequent silanization [J]. Surface and Coatings Technology, 2014, 240: 255 - 260.

Liao W, Jiang F, Zhang Y, et al. Highly-conductive composite bipolar plate based on ternary carbon materials and its performance in redox flow batteries [J]. Renewable Energy, 2020, 152: 1310 - 1316.

Greenwood P, Thring R H, Chen R. Conductive materials for polymeric bipolar plates: Electrical, thermal and mechanical properties of polyethylene-carbon black/graphite/magnetite blends [J]. Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications, 2013, 227 (3): 226 - 242.

Naji A, Krause B, Pötschke P, et al. Extruded polycarbonate/Di-Allyl phthalate composites with ternary conductive filler system for bipolar plates of polymer electrolyte membrane fuel cells [J]. Smart Materials and Structures, 2019, 28 (6): 064004.

Stübler N, Hickmann T, Ziegmann G. Effect of methanol absorption on properties of polymer composite bipolar plates for direct methanol fuel cells[J]. Journal of power sources, 2013, 229: 223 - 228.

Kakati B K, Deka D. Differences in physico-mechanical behaviors of resol (e) and novolac type phenolic resin based composite bipolar plate for proton exchange membrane (PEM) fuel cell [J]. Electrochimica Acta, 2007, 52 (25): 7330 - 7336.

Akhtar M N, Sulong A B, Umer A, et al. Multi-component MWCNT/NG/EP-based bipolar plates with enhanced mechanical and electrical characteristics fabricated by compression moulding[J]. Ceramics International, 2018, 44 (12): 14457 - 14464.

Masand A, Borah M, Pathak A K, et al. Effect of filler content on the properties of expanded-graphite-based composite bipolar plates for application in polymer electrolyte membrane fuel cells [J]. Materials Research Express, 2017, 4 (9): 095604.

Mathur R B, Dhakate S R, Gupta D K, et al. Effect of different carbon fillers on the properties of graphite composite bipolar plate [J]. Journal of Materials Processing Technology, 2008, 203 (1-3): 184 - 192.

Király A, Ronkay F. Effect of graphite and carbon black fillers on the processability, electrical conductivity and mechanical properties of polypropylene-based bipolar plates [J]. Polymers and Polymer Composites, 2013, 21 (2): 93 - 100.

Gautam R K, Kar K K. Synergistic effects of carbon fillers of phenolic resin based composite bipolar plates on the performance of PEM fuel cell [J]. Fuel Cells, 2016, 16 (2): 179 - 192.

Perets Y, Aleksandrovych L, Melnychenko M, et al. The electrical properties of hybrid composites based on multiwall carbon nanotubes with graphite nanoplatelets [J]. Nanoscale research letters, 2017, 12: 1 - 10.

Mathur R B, Dhakate S R, Gupta D K, et al. Effect of different carbon fillers on the properties of graphite composite bipolar plate [J]. Journal of Materials Processing Technology, 2008, 203 (1-3): 184 - 192.

Witpathomwong S, Okhawilai M, Jubsilp C, et al. Highly filled graphite/graphene/carbon nanotube in polybenzoxazine composites for bipolar plate in PEMFC [J]. International Journal of Hydrogen Energy, 2020, 45 (55): 30898 - 30910.

Yao K, Adams D, Hao A, et al. Highly conductive and strong graphite-phenolic resin composite for bipolar plate applications [J]. Energy & fuels, 2017, 31 (12): 14320 - 14331.

Antunes R A, De Oliveira M C L, Ett G, et al. Carbon materials in composite bipolar plates for polymer electrolyte membrane fuel cells: A review of the main challenges to improve electrical performance [J]. Journal of Power Sources, 2011, 196 (6): 2945 - 2961.

Du L, Jana S C. Highly conductive epoxy/graphite composites for bipolar plates in proton exchange membrane fuel cells [J]. Journal of Power Sources, 2007, 172 (2): 734 - 741.

Adloo A, Sadeghi M, Masoomi M, et al. High performance polymeric bipolar plate based on polypropylene/graphite/graphene/nano-carbon black composites for PEM fuel cells[J]. Renewable Energy, 2016, 99: 867 - 874.

Yu S, Wong W M, Hu X, et al. The characteristics of carbon nanotube‐reinforced poly (phenylene sulfide) nanocomposites [J]. Journal of Applied Polymer Science, 2009, 113 (6): 3477 - 3483.

Boyaci San F G, Tekin G. A review of thermoplastic composites for bipolar plate applications [J]. International journal of energy research, 2013, 37 (4): 283 - 309.

Soares da Silva J P, Soares B G, Silva A A, et al. Double percolation of melt-mixed PS/PBAT blends loaded with carbon nanotube: Effect of molding temperature and the non-covalent functionalization of the filler by ionic liquid [J]. Frontiers in Materials, 2019, 6: 191.

Yui H, Wu G, Sano H, et al. Morphology and electrical conductivity of injection-molded polypropylene/carbon black composites with addition of high-density polyethylene[J]. Polymer, 2006, 47 (10): 3599 - 3608.

Haghgoo M, Ansari R, Hassanzadeh-Aghdam M K. Prediction of electrical conductivity of carbon fiber-carbon nanotube-reinforced polymer hybrid composites [J]. Composites Part B: Engineering, 2019, 167: 728 - 735.

Chaiwan P, Pumchusak J. Wet vs. dry dispersion methods for multiwall carbon nanotubes in the high graphite content phenolic resin composites for use as bipolar plate application [J]. Electrochimica Acta, 2015, 158: 1 - 6.

Lee H E, Chung Y S, Kim S S. Feasibility study on carbon-felt-reinforced thermoplastic composite materials for PEMFC bipolar plates [J]. Composite Structures, 2017, 180: 378 - 385.

Lee H E, Han S H, Song S A, et al. Novel fabrication process for carbon fiber composite bipolar plates using sol gel and the double percolation effect for PEMFC[J]. Composite Structures, 2015, 134: 44 - 51.

Alo O A, Otunniyi I O, Pienaar H, et al. Electrical and mechanical properties of polypropylene/epoxy blend-graphite/carbon black composite for proton exchange membrane fuel cell bipolar plate [J]. Materials Today: Proceedings, 2021, 38: 658 - 662.

Yui H, Wu G, Sano H, et al. Morphology and electrical conductivity of injection-molded polypropylene/carbon black composites with addition of high-density polyethylene [J]. Polymer, 2006, 47 (10): 3599 - 3608.

Nguyen L, Mighri F, Deyrail Y, et al. Conductive materials for proton exchange membrane fuel cell bipolar plates made from PVDF, PET and co‐continuous PVDF/PET Filled with carbon additives [J]. Fuel Cells, 2010, 10 (6): 938 - 948.

Downloads

Published

11-06-2024

How to Cite

Li, W. (2024). Research Progress and Prospects of Bipolar Plate Materials for Proton Exchange Membrane Fuel Cells . Highlights in Science, Engineering and Technology, 104, 130-154. https://doi.org/10.54097/r7damr19