Influence of Ultrasonic Rolling Process Parameters on Residual Stress of Tooth Root

Huicun Shen; Xiao Shen; Junhua Chen; Yunqian Chen

doi:10.54097/hset.v20i.3947

Authors

Huicun Shen
Xiao Shen
Junhua Chen
Yunqian Chen

DOI:

https://doi.org/10.54097/hset.v20i.3947

Keywords:

Ultrasonic Rolling; 12Cr2Ni4A; Tooth Root; Process Parameters; Residual Stress.

Abstract

The finite element model of ultrasonic rolling of 12Cr2Ni4A gear was established by ANSYS software, and the distribution law of residual stress field of tooth root after ultrasonic rolling was analyzed. A 12Cr2Ni4A gear ultrasonic rolling test platform was built to study the effect of process parameters on the residual stress of ultrasonic rolling tooth roots, and the finite element model was verified at the same time.

Downloads

Download data is not yet available.

References

HE Shao-jie, YANG Wen-yu, GUO Bu-peng, et al. Research progress on evaluation of surface residual stress and fatigue life of machined products[J]. Surface technology, 2015, 44(6): 120-126.

LI You-guo, KANG Guo-zheng, WANG Chang-an, et al. Effect of residual stresses on the crack initiation life for rolling contact fatigue[J]. Journal of Tsinghua University (science and technology), 2005, 45(12): 1664-1667.

SHAW L L, TIAN J W, ORTIZ A L, et al. A direct comparison in the fatigue resistance enhanced by surface severe plastic deformation and shot peening in a C-2000 super alloy[J]. Materials science & engineering, 2010, 527(4-5): 986-994.

MORDYUK B N, IEFIMOV M O, PROKOPENKO G I, et al. Structure, micro-hardness and damping characteristics of Al matrix composite reinforced with AlCuFe or Ti using ultrasonic impact peening[J]. Surface & coatings technology, 2010, 204(9-10): 1590-1598.

MOUSAVI S A A A, FEIZI H, MADOLlAT R. Investigations on the effects of ultrasonic vibrations in the extrusion process[J]. Journal of materials processing technology, 2007, 187-188(12): 657-661.

JIANG J J, ZHENG J X, LIU C S. Research on surface roughness of ultrasonic polishing without abrasive based on orthogonal experiments[J]. Key engineering materials, 2009, 416(8): 133-136.

WANG T, WANG D, LIU G, et al. Investigations on the nano crystallization of 40Cr using ultrasonic surface rolling processing[J]. Applied surface science, 2008, 255(5): 1824-1829.

HUANG Shi-qiao, CAO Guo-bing, PENG Min, et al. Experimental calculating the surface roughness of SUS304 steel produced by the vibratory ball burnishing process[J]. Journal of Sichuan University (science and technology), 1990, 51(3): 1-8.

ZHENG Jian-xin, JIANG Shu-xiang. Residual stress field in the process of 2D ultrasonic rolling 7050 aluminum alloy[J]. Surface technology, 2017, 46(12): 265-269.

JIAO Feng, LAN Shuai-ling, WANG Yi, ZHAO Bo. Residual Stress Characteristics and Parameters Optimization of Ultrasonic Rolling 12Cr2Ni4A Gear Steel[J]. Surface technology, 2020, 49(11): 334-341.

ZHAO Yun-cai, WEN Chun-bin. Simulation of 3D residual stress field of ultrasonic surface rolling by dynamic finite element analysis[J]. Journal of mechanical strength, 2017, 39(4): 875-881.

LIU Y, WANG L, WANG D. Finite element modeling of ultrasonic surface rolling process[J]. Journal of materials processing technology, 2011, 211(12): 2106-2113.