A Saw Blade Drill Bit with Reduced Heat Loss

Authors

  • Sufang Han
  • Shenghan Wang
  • Zihan Zhao
  • Zhao Li

DOI:

https://doi.org/10.54097/xp0xpx60

Keywords:

Fe-Co-Cu Binder; Microwave Non-Pressure Sintering; Density; Wear Resistance; Energy Conservation.

Abstract

We adopt microwave sintering technology prepared a low-cobalt Fe-Co-Cu diamond saw blade bit. The bit can achieve densification sintering which meets the index of diamond saw blade heads. Furthermore, the use of microwave non-pressure sintering significantly shortens the total sintering time and saves more than 20% energy. This environmentally friendly saw blade head can stimulate the development of the sawing industry and would be vastly used in the field of high and new technologies.

Downloads

Download data is not yet available.

References

[1] Handschuh-Wang S, Wang T, Tang Y B. Ultrathin Di-amond Nanofilms-Development, Challenges, and Applic-ations[J], Small, 2021,17(30).

[2] Jian Z, Xu J, Yang N J et al. A perspective on diamond composites and their electrochemical applic-ations[J],Current Opinion in Electrochemistry,2021,30.

[3] J Qin J, Yang W, Long W M et al. Research progress of additive technology of diamond and its composite materials [J], Transactions of the China Wel-ding Institution, 2022, 43 (8): 102-112.

[4] Ranjbar O, Rassekh F. The impact of financial development on income convergence: An application of two exogenous growth models[J],International Review of Economics & Finance, 2017, 50: 65-74.

[5] Hang W, Liang N J, Liu, Y Z et al. Cobalt-Catalyzed Highly Regioselective Three-Component Arylca-rboxylation of Acrylate with Aryl Bromides and Carbon Dioxide[J], Chemsuschem, 2021,14(22):4941-4946.

[6] Rinkevich A B, Kuznetsov E A, Milyaev M A et al. Transmission of Microwaves through Magnetic Metallic Nanostructures[J],Physics of Metals and Metallography, 2020, 121(12): 1137-1167.

[7] Tsay C Y, Liu K S, Lin I N. Microwave sinteringof (Bi0.75Ca1.2Y1.05)(V0.6Fe4.4) O12 microwave mag-netic materials[J],Journal of the European Ceramic Society, 2004, 24 (6): 1057-1061.

[8] Lin S, Xiong W. Microstructure and abrasive behaviors of TiC-316L composites prepared by warm compaction and microwave sintering[J],Advanced Powder Technology the International Journal of the Society of Powder Technology Japan,2012,23(3):419-425.

[9] Bao R, Guo S, Yi J et al. Microwave reaction sintering on WC-Co cemented carbides fabrication[J],The Chinese Journal of Nonferrous Metals,2020,30(8):1828-1836.

[10] Moratal S, Benavente R, Salvador M D et al. Microwave sintering study of strontium-doped lanthanum manganite in a single-mode microwave with electric and magnetic field at 2.45 GHz[J],Journal of the European Ceramic Society,2022,5624-5630.

[11] Amiri T, Etsell T H, Sarkar P. Direct Microwave Sintering of Poorly Coupled Ceramics in Electrochemical Devices[J], Journal of Electrochemical Science and Technology, 2022, 13(3): 390-397.

[12] Batienkov R V, Bol'shakova A N, Khudnev A A. Microwave Sintering of Metal Powder Materials (Review) [J],Metallurgist, 2022, 65(9-10):1163-1173.

[13] Gao L P, Li G R, Wang H M et al. Interfacial structure and properties of microwave sintered FeCoNi1.5CrCu/ Al composites[J],Materials Characterization,2022,189.

[14] Wang X X, Liu Z H, Tang Y H et al. Low temperature and rapid microwave sintering of Na3Zr2Si2PO12 solid electrolytes for Na-Ion batteries[J],Journal of Power Sources, 2021, 481.

[15] Xu D W, Chen P, Chen G Z et al. Self-assembly synthesis and microwave absorption properties of magnetic functionalized graphene aerogels[J],Chinese Science Bulletin-Chinese,2022, 67 (4-5):437-446.

[16] Blachnio J, Spychala J, Zasada D. Analysis of structural changes in a gas turbine blade as a result of high temperature and stress [J],Engineering FailureAnalysis,2021,127.

[17] Cocker T L, Baillie D, Buruma M et al. Micro-scopic origin of the Drude-Smith model[J],Physical Review,2017,96(20).

[18] Dang D T-X, Vu T H T. Enhancing photoluminescence of Au – TiO2 nanoparticles using Drude model[J],Journal of IKEEE,2017,21(3):288-296.

[19] Lin L, Wen Q, Wang C. Structural topology optimization of circular saw blade[J],Journal of Machine Design,2018,35 (6): 24-28.

[20] Zhou Y, Zhao X, Xu H. Failure analysis on fatigue crack of bimetal strip saw blade[J],Heat Treatment of Metals,2016, 41 (6):176-179.

[21] Xiao C, Dou Z, Li J et al. Study on the properties of diamond saw blades prepared by Cu-based pre-alloyed powders [J], Powder Metallurgy Technology,2018,36(4): 287-291.

[22] Siklienka M, Kminiak R, Argay F et al. Process Characteristics of Horizontal Log Band Saw in Cutting Frozen Beech[J],Drvna Industrija, 2015,66(1):41-48.

[23] Litvinov A E, Buzko V Y, Balaev E Y et al. Technological aspects of wear-resistant coating treatment on the surface of a cutting tool[J],Cis Iron and Steel Review,2021,22:111-116.

[24] Chucheep T, Mahathaninwong N, Janudom S. The cost benefit analysis of reduced wear bandsaws[J],South African Journal of Industrial Engineering,2020,31(1):1-11.

[25] Tang L M, Pan Z B, Zhao J H et al. Significantly ceramics via optimized sintering aids[J],Journal of Alloys and Compounds, 2023, 935.

[26] Feng J J, Zhang Y R, Ma M S et al. Current Status and Development Trend of Cold Sint-ering Process[J],Journal of Inorganic Materials,2023,38(2):125-136.

Downloads

Published

14-09-2024

Issue

Section

Articles

How to Cite

Han, S., Wang, S., Zhao, Z., & Li, Z. (2024). A Saw Blade Drill Bit with Reduced Heat Loss. Academic Journal of Science and Technology, 12(2), 121-124. https://doi.org/10.54097/xp0xpx60