Research and Design of Automatic Pipe Blanking Device Based on Adaptive Control

Authors

  • Guilin Fu
  • Ang Zheng
  • Yijun Zhao
  • Hang Liu

DOI:

https://doi.org/10.54097/ajst.v4i2.4189

Keywords:

Cutting method, Automatic blanking, Adaptive control.

Abstract

In the development of the modern processing and manufacturing industry, because of the increasingly fierce market competition, processing, and manufacturing enterprises, to further control the cost and improve efficiency, optimize the cutting technology to improve the utilization rate of raw materials. In some factories and workshops that have a demand for pipes, such as the assembly of the whole structure of aircraft, in the process of welding, assembling and molding the frame, the demand for the strength of pipes is high. Cuts made by hydraulic disk saw or toothless saw are not conducive to welding, and can't meet the use requirements, thus affecting the installation or assembly process of other spare parts and reducing production efficiency. In this paper, the design principle and scheme of automatic pipe-cutting technology based on adaptive control are discussed. It is very important to save raw materials by rationally optimizing the cutting technology and making a scientific cutting plan, to reduce the cost of enterprises and improve the benefits of enterprises.

Downloads

Download data is not yet available.
<br data-mce-bogus="1"> <br data-mce-bogus="1">

References

O. I, Tacha, Ch. K, et al. Analysis, adaptive control and circuit simulation of a novel nonlinear finance system[J]. Applied Mathematics and Computation, 2016, 276(1):200-217.

Nasir S, Gangopadhyay S, Raychowdhury A. All-Digital Low-Dropout Regulator With Adaptive Control and Reduced Dynamic Stability for Digital Load Circuits[J]. IEEE Transactions on Power Electronics, 2016, 31(12):8293-8302.

Tacha O I, Volos C K, Stouboulos I N, et al. Analysis, adaptive control and circuit simulation of a novel finance system with dissaving[J]. Archives of Control Sciences, 2016, 26(1):95-115.

Pourseif T, Andani M T, Ramezani Z, et al. Model Reference Adaptive Control for Robot Tracking Problem: Design & Performance Analysis[J]. International Journal of Control Science and Engineering, 2017, 7(1):18-23.

He S, Kasdin N J, Vanderbei R. Identification and adaptive control of a high-contrast focal plane wavefront correction system[J]. Journal of Astronomical Telescopes, Instruments, and Systems, 2018, 4(4):1.

Zhai D H, Xia Y. Adaptive Control for Teleoperation System With Varying Time Delays and Input Saturation Constraints[J]. IEEE Transactions on Industrial Electronics, 2016, 63(11): 6921-6929.

He H, Guler S I, Menendez M. Adaptive control algorithm to provide bus priority with a pre-signal[J]. Transportation Research Part C Emerging Technologies, 2016, 64:28-44.

El-Samahy A A, Shamseldin M A. Brushless DC motor tracking control using self-tuning fuzzy PID control and model reference adaptive control[J]. Ain Shams Engineering Journal, 2016, 9( 3):341-352.

Pucci D, Romano F, Nori F. Collocated Adaptive Control of Underactuated Mechanical Systems[J]. IEEE Transactions on Robotics, 2017, 31(6):1527-1536.

Buchstaller D, French M. Robust Stability for Multiple Model Adaptive Control: Part II—Gain Bounds[J]. IEEE Transactions on Automatic Control, 2016, 61(3):693-708.

Downloads

Published

04-01-2023

How to Cite

Fu, G., Zheng, A., Zhao, Y., & Liu, H. (2023). Research and Design of Automatic Pipe Blanking Device Based on Adaptive Control. Academic Journal of Science and Technology, 4(2), 133–136. https://doi.org/10.54097/ajst.v4i2.4189

Issue

Section

Articles