Reliability evaluation of electro spindle based on no-failure data
DOI:
https://doi.org/10.54097/hset.v16i.2413Keywords:
Electro Spindle, E-Bayes Method, No-failure Data, Reliability Estimation.Abstract
Electric spindle is a key functional component of CNC machining equipment including CNC machine tools, and its reliability level is a key bottleneck factor restricting the reliability of high-end CNC equipment. So far, the research on the reliability evaluation method of electric spindle is still in its infancy, and there is a lack of Systematic and complete theoretical support. The motorized spindle is a typical high-reliability and long-life product, and it is difficult to fail or fail due to obvious performance degradation within a limited test time. Therefore, the traditional reliability evaluation method based on statistical theory is not effective. Therefore, it is of great significance to carry out the early reliability test of the motorized spindle and the reliability evaluation of the motorized spindle without failure data, which is of great significance to reasonably evaluate the reliability level of the motorized spindle. At present, when there is no failure data or very little failure data for the motorized spindle of the machine tool, only the point estimate of the parameter or the one-sided confidence interval of the parameter can be calculated, and it is extremely difficult to obtain the point estimate and the interval estimate at the same time, which will affect the reliability analysis results. Consistency. In order to solve this problem, this paper takes a certain type of CNC machine tool motorized spindle as the research object, and determines the monitoring points and monitoring information according to the failure analysis of similar motorized spindles; combines the test information to evaluate the reliability of the motorized spindle without failure data. The reliability evaluation method of the motorized spindle proposed in this paper can effectively avoid the problem that the traditional method cannot be analyzed when there is no failure data, and provides a new idea for the reliability evaluation of the motorized spindle.
Downloads
References
D. W. Coit, "Maximization of system reliability with a choice of redundancy strategies," IIE transactions, vol. 35, no. 6, pp. 535-543, 2003.
Y. Yan, "A new nonlinear neural network for solving QP problems," in International Symposium on Neural Networks, 2014: Springer, pp. 347-357.
X. Liu, J. Li, K. N. Al-Khalifa, A. S. Hamouda, D. W. Coit, and E. A. Elsayed, "Condition-based maintenance for continuously monitored degrading systems with multiple failure modes," IIE transactions, vol. 45, no. 4, pp. 422-435, 2013.
M. Fan, Z. Zeng, E. Zio, and R. Kang, "Modeling dependent competing failure processes with degradation-shock dependence," Reliability Engineering & System Safety, vol. 165, pp. 422-430, 2017.
C. Fan, Z. Lu, and Y. Shi, "Time-dependent failure possibility analysis under consideration of fuzzy uncertainty," Fuzzy Sets and Systems, vol. 367, pp. 19-35, 2019.
A. Peiravi, M. Karbasian, M. A. Ardakan, and D. W. Coit, "Reliability optimization of series-parallel systems with K-mixed redundancy strategy," Reliability Engineering & System Safety, vol. 183, pp. 17-28, 2019.
G. Shen, W. Zeng, C. Han, P. Liu, and Y. Zhang, "Determination of the average maintenance time of CNC machine tools based on type II failure correlation," Eksploatacja i Niezawodność, vol. 19, no. 4, 2017.
c. h. guixiang shen, el al, "Fault Analysis of Machine Tools Based on Grey Relational Analysis and Main Factor Analysis," in Journal of Physics: Conference Series, 2019, vol. 1069: iop science, p. 012112.
Z. Wang, J. Yang, G. Wang, and G. Zhang, "Application of three-parameter Weibull mixture model for reliability assessment of NC machine tools: a case study," Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, vol. 225, no. 11, pp. 2718-2726, 2011.
Z.-M. Wang and J.-G. Yang, "Numerical method for Weibull generalized renewal process and its applications in reliability analysis of NC machine tools," Computers & Industrial Engineering, vol. 63, no. 4, pp. 1128-1134, 2012.
J. Guo, D. Wang, W. Chen, and R. Fan, "Multiaxis loading device for reliability tests of machine tools," IEEE/ASME Transactions on Mechatronics, vol. 23, no. 4, pp. 1930-1940, 2018.
Z. Mu, G. Zhang, Y. Ran, S. Zhang, and J. Li, "A reliability statistical evaluation method of CNC machine tools considering the mission and load profile," IEEE Access, vol. 7, pp. 115594-115602, 2019.
T.-j. Li, J.-h. Yuan, Y.-m. Zhang, and C.-y. Zhao, "Time-varying reliability prediction modeling of positioning accuracy influenced by frictional heat of ball-screw systems for CNC machine tools," Precision Engineering, vol. 64, pp. 147-156, 2020.
Y. Du, G. Wu, Y. Tang, H. Cao, and S. Liu, "Reliability allocation method for remanufactured machine tools based on fuzzy evaluation importance and failure influence," International Journal of Precision Engineering and Manufacturing-Green Technology, vol. 8, no. 6, pp. 1617-1628, 2021.
Downloads
Published
Issue
Section
License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
